Lilbuckgetter
Well-Known Member
i just bought a wildview extreme2 trail camera and i dont know how to set it up? anybody know how or any idea????
-
Help Support TNDeer:
how to setup trail camera????
- Thread starter Lilbuckgetter
- Start date
stik
Well-Known Member
no directions?
cecil30-30
Well-Known Member
They are pretty straight foward,its not rocket science. Put you a mineral/salt block out and put the camera in front of it,this time of year you will get alot of pics.
Lilbuckgetter
Well-Known Member
my brother gave it too me and he took it out of the box and threw the box away. its never been used but once. i just dont know how to do it
Lilbuckgetter
Well-Known Member
i need to know how to set up the actual camera.. on the inside it says cam- test off or pir/ time out 1 5 10 20/ resoultion hi and lo/ burst- 1 2 3 avi/ flash auto on off/ than has three big buttons that says up on and set so idk how to set it up and what it needs to be on
tn droptine
Well-Known Member
Here is a link to a pdf version of the manual for that camera:
http://www.trailcampro.com/miscfiles/Wi ... ,%20X5.pdf
http://www.trailcampro.com/miscfiles/Wi ... ,%20X5.pdf
Lilbuckgetter
Well-Known Member
it wont let me download it or whatever u have to do
tn droptine
Well-Known Member
Here is the directions for programming, taken from the manual:
Programming your Wildview Camera
The following setting must be performed before you
turn on the camera.
1. Select the time out interval by sliding the time out
toggle switch to the desired preset time interval in
minutes. 1 / 5 / 10 / 20 minutes.
2. Select the resolution setting by sliding the resolution
toggle switch to the desired resolution setting. Hi /
Lo resolution.
3. Select the Flash mode: Slide the switch to either
Auto / On / Off position.
a. Auto � Flash on based on surround light conditions.
b. On � Flash on for every image captured
c. Off � No Flash will go off.
4. Select Burst mode: Slide the switch to 1 / 2 / 3 / AVI
position. If you choose AVI mode, the camera will
automatically switch to 1 picture mode if it detects a
low light source.
5. Turn on the Camera to set the Date / Time stamp
a. Slide the power switch to the PIR position
b. Press and hold [SET] button for 2 seconds to
enter date & time setting mode.
c. Time and HH will blink. Press [UP] or [DN] to
adjust the hour
d. Press [SET] button to enter minute setting. Time
and MM will blink. Press [UP] or [DN] to adjust
the minute.
e. Press [SET] button to enter the month setting.
Date & MM will blink. Press [UP] or [DN] to
adjust month.
f. Press [SET] button to enter date setting. Date &
DD will blink. Press [UP] or [DN] to adjust date.
g. Press [SET] button to enter year setting. Date &
YY will blink. Press [UP] or [DN] to adjust year.
h. Press and hold [SET] button for 2 seconds to exit
the setting mode and enter into PIR count down
mode. Display will show date and number of
picture taken.
Programming your Wildview Camera
The following setting must be performed before you
turn on the camera.
1. Select the time out interval by sliding the time out
toggle switch to the desired preset time interval in
minutes. 1 / 5 / 10 / 20 minutes.
2. Select the resolution setting by sliding the resolution
toggle switch to the desired resolution setting. Hi /
Lo resolution.
3. Select the Flash mode: Slide the switch to either
Auto / On / Off position.
a. Auto � Flash on based on surround light conditions.
b. On � Flash on for every image captured
c. Off � No Flash will go off.
4. Select Burst mode: Slide the switch to 1 / 2 / 3 / AVI
position. If you choose AVI mode, the camera will
automatically switch to 1 picture mode if it detects a
low light source.
5. Turn on the Camera to set the Date / Time stamp
a. Slide the power switch to the PIR position
b. Press and hold [SET] button for 2 seconds to
enter date & time setting mode.
c. Time and HH will blink. Press [UP] or [DN] to
adjust the hour
d. Press [SET] button to enter minute setting. Time
and MM will blink. Press [UP] or [DN] to adjust
the minute.
e. Press [SET] button to enter the month setting.
Date & MM will blink. Press [UP] or [DN] to
adjust month.
f. Press [SET] button to enter date setting. Date &
DD will blink. Press [UP] or [DN] to adjust date.
g. Press [SET] button to enter year setting. Date &
YY will blink. Press [UP] or [DN] to adjust year.
h. Press and hold [SET] button for 2 seconds to exit
the setting mode and enter into PIR count down
mode. Display will show date and number of
picture taken.
Lilbuckgetter
Well-Known Member
thanks.
Lilbuckgetter
Well-Known Member
still not working. i dont know wat is wrond with it
