• Help Support TNDeer:

Help with split brass

4

44 mag

Well-Known Member
Joined
Jul 11, 2019
Messages
1,057
Location
Dickson
I loaned a buddy a youth model CVA Scout in 243. I also gave him a box of factory new ammo for his son to use the rest of season. He took it to the range today to confirm zero and one of the 6 rounds he fired had a split case. This gun has not been fired in several years due to my oldest outgrowing it and my youngest not being big enough. I have never had a problem in the past.

My question is, is this one case just a fluke or bad case? Or is it something to be concerned with.
 

Attachments

  • IMG_0838.webp
    IMG_0838.webp
    80.3 KB · Views: 1
  • IMG_0837.webp
    IMG_0837.webp
    55.1 KB · Views: 1
I'd want to see the other cases as well to see if there were any tell tale marks of other possible splits. How many rounds had been fired thru it since you've had it? Do you still have brass for those firings to check also? I would hope that it's a bad case, but you can't be too careful with this issue bc you may have a chamber issue that's just now becoming apparent. Look the bore over well, with a borescope if possible, to check for abnormalities. I would not fire it again until I was sure I knew what the problem is/was.
 
MUP said:
I'd want to see the other cases as well to see if there were any tell tale marks of other possible splits. How many rounds had been fired thru it since you've had it? Do you still have brass for those firings to check also? I would hope that it's a bad case, but you can't be too careful with this issue bc you may have a chamber issue that's just now becoming apparent. Look the bore over well, with a borescope if possible, to check for abnormalities. I would not fire it again until I was sure I knew what the problem is/was.
Click to expand...
I do have the other brass that was fired through the gun prior to today, but I will have to find it rifle. Probably hasn't had 20 rounds total fire through it. I told my buddy to save all the brass so that I can look at it so hopefully I will have that as well soon.
 
nso123 said:
It might be the picture, but the brass looks kind of tarnished to me. Is there a chance it had some corrosion on the case?
Click to expand...
I can't say for sure about the corrosion on the brass. Hopefully I will get the rest of the brass when I get the gun back to inspect it.
 
Pressure. Ive got a tikka 25-06 that i needed a load for. Back in the spring, I loaded a progression and left it in a casegard over the summer. In October I was getting a few ready for possible hunting out to 400yds. I took the 26-06 and shot the progression. To my amazement, 3 out of 12 pieces of brass split down the side. I shelved it til after season. A couple weeks later I was working on a subsonic suppressed 45-70 load. The bullet seater die did not work properly. Upon further investigation, the bullet seater dies had been swapped between 45-70 and 25-06. That was od as I never have more than one set of dies out at once. It had been several years since loading for either one. Then it hit me. My grandson would hang out with me in the hobby room when he was 5 or so yo. He must have swapped them. Apparently the bullets were seated at a slight angle and some made excessive pressure. If I had checked them on my concentricity tool it would have shown up.
 
Last edited:
jlanecr500 said:
Pressure. Ive got a tikka 25-06 that i needed a load for. Back in the spring, I loaded a progression and left it in a casegard over the summer. In October I was getting a few ready for possible hunting out to 400yds. I took the 26-06 and shot the progression. To my amazement, 3 out of 12 pieces of brass split down the side. I shelved it til after season. A couple weeks later I was working on a subsonic suppressed 45-70 load. The bullet seater die did not work properly. Upon further investigation, the bullet seater dies had been swapped between 45-70 and 25-06. That was od as I never have more than one set of dies out at once. It had been several years since loading for either one. Then it hit me. My grandson would hang out with me in the hobby room when he was 5 or so yo. He must have swapped them. Apparently the bullets were seated at a slight angle and some made excessive pressure. If I had checked them on my concentricity tool it would have shown up.
Click to expand...
Over pressure was my first thought as well. That's why I had him send me the head stamp
picture, and it looks fine best I can tell in the picture.

This is factory loaded Hornady Custom Lite ammo. Supposed to be reduced recoil. I will admit that the box of ammo I gave him was several years old and I didn't open it to inspect the brass for corrosion. But it is stored in a cool dry location with the rest of my ammo.
 
Maybe the powder went bad. It can go bad in 2 ways. It can burn slower or it can burn faster than designed. Powders with a high nitro content tend to burn faster as they go bad, making them hotter.
 

Latest posts

Back
Top